Car Radio Supplies Cheapest Parts On the Web

Channel Power Amplifier

Thanks for visiting our site!
Channel Power Amplifier
Checkout Ebay Auctions For The Cheapest Prices

Check out Amazon:

Account limit of 2000 requests per hour exceeded.

Featured Article: Channel Power Amplifier:

Surround sound use to be only for your home entertainment needs, now, it has proceeded to the car audio market. Surround sound focuses on creating a 3d listening experience, which combines ambience and a wide range of frequencies. To incorporate it into your car, you will need patience and a bit of time set aside, but it is without doubt worth it!

When commencing on the project, start out by planning where the speakers and subwoofers are going to be placed. They need to be place just close enough to the passengers, but not too close or far away, in order to get the most out of your car audio system.

You will be placing four speakers in total in the corners of your car, plus subwoofers. The speakers will be placed in the four corners of the car above the level of the ear in order to gain the highest quality surrounding ambient sound. Remember, it requires quite a bit of power, so purchase a five channel amplifier, which will feed enough power into your speakers.

A centre speaker may also be needed. This speaker is often incorporated into the dashboard with a tweeter - a loudspeaker that can pick up high frequencies. A crossover will also be needed to separate the frequencies. These can either be bought separately or are incorporated into amplifiers.

If you are purchasing a new stereo, you will need a unit that can plug into a surround sound processor. Since the signal is digital in this special sound processor, the stereo needs to be able to relay digital signals as well. If your stereo is not digital, then opt for a surround sound processor that converts analogue to digital.

Surround sound enables you to experience 3d sound in your own car. With surround sound, you will never feel you're missing out on the full listening experience.

If interested in car audio and other components, have a look at www.bassjunkies.com

Car Audio Amplifier Overview

Your amplifier takes the signal from your head unit and makes it big enough to be able to drive your speakers. It is preferable to use separate amps for high and low frequencies but it is not necessary. The problem with using one amp for all frequencies is that you cannot adjust the levels among different frequency ranges as easily as you can adjust outputs of separate amps.  Many people begin their system with an amplifier for the low frequencies (bass) and use their head units built-in power to drive the higher frequency speakers. This is enough but the built-in power in a head unit is usually not strong enough for high volume listening and not clean enough for the discerning ear. There are lots of choices when choosing an amplifier.

Things to look for:
RMS Power: The power output of an amplifier should be roughly matched to what the amp will be used for and what speakers it will be driving. Oddly enough, the most regular problem with matching speakers and amps is using an amp that is too weak to power the speaker. When an underpowered amp is used to power a speaker, the listener tends to turn the volume up higher in order to get more output of the amplifier. This usually leads to the amplifier running to its limit and distorting. This distortion can cause the output from the amplifier to become DC for short periods of time and DC signals of even low power can damage a speaker. Under powering a speaker in this way can be more dangerous than overpowering it! Also greater power is usually needed when powering subwoofers because of their greater size and excursion. Do not plan on using an amp of less than 75watts per channel to drive a subwoofer. The converse holds true for higher frequencies (midrange and treble) only 25-50watts per channel are needed to drive speakers in those frequency ranges, however more power will not hurt, it just probably will not be used. Another factor in power output is stability in low resistance loads. It is possible to wire mutiple subwoofers to a single channel on an amplifier but the amp will have to work harder to drive this kind of load.  Many affordable priced amps can drive loads as low as 2 ohms or less, with 4 ohms being the typical load of a single speaker.
 
Power Supply Regulation: The power supply in an amplifier converts the 12volt DC that is available in your car's electrical system to something the amp can use to produce greater power. Several designs are used by manufacturers today. Two categories are regulated and unregulated. A regulated supply produces the same power regardless of whether your car's electrical system voltage sags (which a capacitor will help prevent).   An unregulated supply's power output depends directly on the input voltage. This causes changes in the maximum output power with changes in the car's electrical system. I recommend getting an amp with a regulated power supply so power output will be constant regardless of input voltage changes. This changes if you have a stiffening capacitor or another regulation device (Accumatch) to smooth out your car's electrical system. In this case, buy an amp with an unregulated supply. Some cheap amps use unregulated supplies to save money but provide none of the benefits of a regular unregulated supply. One way to determine whether an amp has a regulated supply or not is to view the power output specs for 12volt and 14.4volt inputs. If they are the same then the amp probably has a regulated supply otherwise it has an unregulated one.

Tri-Mode: A few amps can play in what is called "tri-mode." In this mode, 2 channels are used to drive a pair of high frequency speakers and one subwoofer. The subwoofer receives power from both channels. This is a very efficient way to use an amp for more than one purpose. A special crossover is required to separate the two ranges of frequencies and it should have a way of adjusting the output level between the high frequency speakers and the subwoofer.  This is a good way to save some money. 

Other Specs: THD (Total Harmonic Distortion) is a specification that often shows up with the power output spec. An example would be "45wattsx2 @ 0.01% THD" This spec says that at an output level of 45watts into each channel the THD will be no more than 0.01%. At times manufacturers will quote the power spec at a THD of 1%. Be wary of this, 1% THD is low quality and either implies that the amp is not very good or that the manufacturer is artificially increasing the power output spec by running the amp into a higher distortion region where it does produce more power but more distortion as well. Either way it is a sign of a low amp or marketing that deceives. Anything lower than 0.1% is negligible.

Built-in Crossovers: These allow you to use the amp to only amplify certain frequencies and dedicate the amp to a subwoofer or some other specialized speaker. By using an amplifier's built-in crossover you eliminate the need for a separate one which can save you quite a bit of money. 

Pre-amp Outputs: Some amps have pre-amp outputs which allow you to "daisy-chain" multiple amps together without splitting the pre-amp output from your head unit. Also, if the amp has a built-in crossover, you can use it to drive another amp. 

Car Audio Amplifiers are available wholesale at http://www.apex-audio.com

About the Author

Professor Apex is an Expert In Car Audio and Mobile Video. He has more than 13 years of experience. You can find him here: Wholesale Car Audio

I have a Kenwood 350W 2 Channel Power Amplifier?

I have a box that will fit a 10" round sub yet I have no idea what the amp is capable of powering. Can you please tell me the best subs i can use and what is the max power the sub can be.
Its a KAC-5203 if that helps
http://www.kenwoodusa.com/Car_Entertainment/2007_Car_Entertainment/KAC-5203

without any more info 350W is going to be the Total power that the amp will put out. ans since it is a two channel that is going to be 175 Peak per channel. the amp might be able to be bridged to produce 350 into one channel but without more info i cant say for sure. Assuming the Amp supports bridge a respectful way to figure out the RMS power(which is actually the power we care about) is to cut the Peak power in half that would be 175Rms/350Peak Amp.

So again without any more info look for a ten inch sub that can handle at least 175watts RMS

Sony STR-DA5600ES, STRA-DA4600ES and STR-DA3600ES AV Receiver launched
Besides the new Sony BDP-S1700ES 3D Blu-ray player, Sony unveiled three more new components in their high-end ES series today. New members in the Elevated Standard (ES) series are the AV receivers STR-DA5600ES, STRA-DA4600ES, and STR-DA 3600ES. Sony...

Thanks for visiting!